PGI User Forum
 SearchSearch   MemberlistMemberlist     RegisterRegister   ProfileProfile    Log inLog in 

CUDA-x86.

error: pgcollect-Fatal-unable to find any RC file
Goto page Previous  1, 2
 
Post new topic   Reply to topic    PGI User Forum Forum Index -> Debugging and Profiling
View previous topic :: View next topic  
Author Message
TerryFeagin25932



Joined: 31 Mar 2011
Posts: 6

PostPosted: Thu May 26, 2011 11:49 pm    Post subject: The pgprof.out file Reply with quote

Here are the first lines from pgprof.out if that helps:

PROF NODALL 0 C:\Users\Feagin\Documents\Visual Studio 2010\Projects\PVFProject2\PVFProject2\Win32\Debug\PVFProject2.exe 1306474720 0
h D172-38475 8176 0 1 0.000000
I 6 GenuineIntel penryn-64 win32 2 2 3067
t 1 2414
E 1 Seconds
p 0
f <unknown>
r [System_Time] 0 0 0 0 0 0 0
e 13.1237
f C:\Users\Feagin\documents\visual studio 2010\Projects\PVFProject2\PVFProject2\ConsoleApp.f90
r tletspec 80 834 0 0 0 4081a0 492
e 0.0309278
l 842 0 0 0 0 4081a8
l 843 0 0 0 0 4081b2
l 845 0 0 0 0 4081c3
l 847 0 0 0 0 4081d4
l 848 0 0 0 0 4081ea
l 849 0 0 0 0 40822e
l 850 0 0 0 0 408256
l 855 0 0 0 0 408267
l 857 0 0 0 0 4082a3
l 858 0 0 0 0 4082b9
l 859 0 0 0 0 4082d5
l 861 0 0 0 0 4082e6
l 865 0 0 0 0 4082fb
l 866 0 0 0 0 408304
l 867 0 0 0 0 408314
l 868 0 0 0 0 408324
l 869 0 0 0 0 40835a
l 871 0 0 0 0 40836b
l 872 0 0 0 0 408385
l 873 0 0 0 0 408395
l 874 0 0 0 0 4083c0
l 875 0 0 0 0 4083d0
l 877 0 0 0 0 4083ee
l 878 0 0 0 0 408400
l 879 0 0 0 0 40841a
l 880 0 0 0 0 408434
l 881 0 0 0 0 408441
l 882 0 0 0 0 408457
e 0.0309278
a 40845e 0
e 0.0206186
a 40846e 0
e 0.0103093
l 883 0 0 0 0 408475
l 885 0 0 0 0 408486
l 887 0 0 0 0 4084c9
l 888 0 0 0 0 4084f3
l 890 0 0 0 0 40851d
l 891 0 0 0 0 40855a
l 897 0 0 0 0 408597
l 898 0 0 0 0 4085af
l 900 0 0 0 0 4085d0
l 903 0 0 0 0 4085e8
-- More (2%) --
Back to top
View user's profile
mkcolg



Joined: 30 Jun 2004
Posts: 6134
Location: The Portland Group Inc.

PostPosted: Fri May 27, 2011 11:21 am    Post subject: Reply with quote

Hi Terry,

Quote:
Could you tell me where I find out more about how to use one of the
pre-configured PGI DOS or Bash shells?
From your Start button, select "All Programs -> PVF Visual Fortran -> Command Shells -> PVF 2010 Cmd (64)". The 32-bit command shell does not have the "(64)".

Quote:
to the pre-configured PGI DOS shell anywhere in the
pgprof documentation or user's guide. Where can I read about it?
Page 2 of the PVF Users Guide under the section titled "Commands Submenu".

Quote:
pgprof-Warning-Malformed $expr(), nonnumeric value 0-ea
These are more RC configuration file errors. I'm not sure what you did after installing the product, but it seems you did something like delete files or move things around. What might be best at this point is to simply uninstall PVF and then re-install.

Quote:

I've only got 23 hours on a trial license to figure this one out.
That's easily corrected. Send a note to sales@pgroup.com asking for your trial license to be extended. Just let them know you've been having issues and have them refer to me if they have questions.
Quote:

Here are the first lines from pgprof.out if that helps:
The pgprof.out file looks fine.
Quote:
Now, it seems that pgprof is not doing much. I tried opening the file called
pgprof.out, but the window is still not showing anything like the user's
guide says it should.
How did you launch PGPROF? Did you load the executable that you're profiling at the same time as the profile output?

Note that pgcollect is a hardware sample based profiler. For very short runs, like a 'Hello World' program, the execution time may be too short for any samples to be taken.

Hope this helps,
Mat
Back to top
View user's profile
TerryFeagin25932



Joined: 31 Mar 2011
Posts: 6

PostPosted: Sat May 28, 2011 1:50 pm    Post subject: Profiling problems Reply with quote

Thanks for all the answers. I have been reading a lot of the PVF
reference manuals and user's guides (pgitools, pgprofug, pgifortref,
pvfreleasenotesn, pvfref, pvfug, pvfinstall, pgf_accel_prog_model1.3,
etc. ), so I knew one of them must have the answer to my question
about the command shell.

The program that I compiled and then tried to profile is a rather large
program (7014 lines of code). The program is one that NASA has been
using for many years to determine the exposure of astronauts (and
spacecraft) to cosmic radiation. For the input values I gave, it takes
about 30 seconds to run (although for other values it can take up to
30 minutes). So, there should have been enough going on that
the profiler could measure the parameters with no problem(s).

The profiler was launched from the Start>Programs>PGI Visual FORTRAN>
Profiler>PGPROF Performance Profiler. Then I used the OPEN PROFILE
dialog and browsed to the profile: pgprof.out and clicked "Select".
The file was in my VS2010 project directory (down in ...\Win32\Debug).
This is the same directory as the executable. Then I selected the
executable as the "Executable". Then I set the directory for the source
file. Then the pgprof application window is visible but there is no
content. Is there something else I am supposed to do to get it
to start? (am I supposed to select something from one of the
menus (File, Edit, View, Sort, etc.)?

In the meantime,I will assume that there
is not anything else I am supposed to do and
that somehow the installation became messed up. When I hear back
about an extension on the trial license, I should be able to re-install
everything, and try again.

Thanks again,
T e r r y
Back to top
View user's profile
mkcolg



Joined: 30 Jun 2004
Posts: 6134
Location: The Portland Group Inc.

PostPosted: Tue May 31, 2011 1:02 pm    Post subject: Reply with quote

Quote:
Is there something else I am supposed to do to get it to start?
No, that should do it. At the very least, you should see a line which shows the "[System_Time]" taking 13.237 seconds and "tletspec" taking 0.0309278 seconds. Definitely not a blank field.

At list point, unfortunately, my only advice would be to start over with a fresh install and hope that what ever is causing the configuration file error is also causing this problem. If not, then we'll continue until we figure it out.

- Mat
Back to top
View user's profile
Display posts from previous:   
Post new topic   Reply to topic    PGI User Forum Forum Index -> Debugging and Profiling All times are GMT - 7 Hours
Goto page Previous  1, 2
Page 2 of 2

 
Jump to:  
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum


Powered by phpBB © phpBB Group